Suitability of gloves should be determined both by material and quality, the latter of which may vary by manufacturer. Only use equipment tested and approved under appropriate government standards. Risk assessment should be performed to determine if air-purifying respirators are appropriate. Use a respirator with type P100 (USA) or P3 (EN 143) cartridges as a backup to engineering controls. Recommended filter device for short term use: Use suitable respirator when high concentrations are present. Maintain an ergonomically appropriate working environment. Wash hands before breaks and at the end of work. Remove all soiled and contaminated clothing immediately. Keep away from foodstuffs, beverages and feed. TLV (USA) Long-term value: 0.02 mg/m 3 as Coįollow typical protective and hygienic practices for handling chemicals. PEL (USA) Short-term value: 0.1* mg/m 3* as Co (for metal dust and fume) Cobalt(II) chloride hexahydrate (100.0%) Properly operating chemical fume hood designed for hazardous chemicals and having an average face velocity of at least 100 feet per minute.Ĭomponents with limit values that require monitoring at the workplace: EXPOSURE CONTROLS/PERSONAL PROTECTIONĪdditional information about design of technical systems: Store in cool, dry conditions in well-sealed containers. Information about storage in one common storage facility:įurther information about storage conditions: Requirements to be met by storerooms and receptacles: Information about protection against explosions and fires:Ĭonditions for safe storage, including any incompatibilities Store in cool, dry place in tightly closed containers.Įnsure good ventilation at the workplace. See Section 8 for information on personal protection equipment. See Section 7 for information on safe handling Methods and materials for containment and cleanup:ĭispose of contaminated material as waste according to section 13. Keep unprotected persons away.ĭo not allow product to enter drains, sewage systems, or other water courses.ĭo not allow material to penetrate the ground or soil. Personal precautions, protective equipment and emergency procedures If this product is involved in a fire, the following can be released: Special hazards arising from the substance or mixture Use fire-fighting measures that suit the surrounding fire. Indication of any immediate medical attention and special treatment needed Most important symptoms and effects, both acute and delayed Rinse opened eye for several minutes under running water. Immediately wash with soap and water rinse thoroughly. If not breathing, provide artificial respiration. (Hazardous Materials Identification System) P501 Dispose of contents/container in accordance with local/regional/national/international regulationsĭ2A - Very toxic material causing other toxic effects P342+P311 If experiencing respiratory symptoms: Call a POISON CENTER/doctor/. P280 Wear protective gloves/protective clothing/eye protection/face protection. P261 Avoid breathing dust/fume/gas/mist/vapors/spray. P284 In case of inadequate ventilation wear respiratory protection. H360 May damage fertility or the unborn child. H341 Suspected of causing genetic defects. H317 May cause an allergic skin reaction. H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled. The substance is classified and labeled according to the CLP regulation. Labelling according to Regulation (EC) No 1272/2008 Information concerning particular hazards for human and environment: R50/53: Very toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment. R42/43: May cause sensitization by inhalation and skin contact. 1 H317 May cause an allergic skin reaction.Ĭlassification according to Directive 67/548/EEC or Directive 1999/45/EC 1A H360 May damage fertility or the unborn child. 2 H341 Suspected of causing genetic defects. 1 H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled. Relevant identified uses of the substance: Scientific research and developmentĬlassification of the substance or mixtureĬlassification according to Regulation (EC) No 1272/2008 Product Number: All applicable American Elements product codes, e.g. Product Name: Cobalt(II) Chloride Hexahydrate Thin Film Deposition & Evaporation Materials.Additive Manufacturing & 3D Printing Materials.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |